James Clerk Maxwell (1831–1879) was one of the major contributors to physics in the nineteenth century (Figure 16.1.1). Although he died young, he made major contributions to the development of the kinetic theory of gases, to the understanding of color vision, and to the nature of Saturn’s rings. He is probably best known for having combined existing knowledge of the laws of electricity and of magnetism with insights of his own into a complete overarching electromagnetic theory, represented by Maxwell’s equations.
The four basic laws of electricity and magnetism had been discovered experimentally through the work of physicists such as Oersted, Coulomb, Gauss, and Faraday. Maxwell discovered logical inconsistencies in these earlier results and identified the incompleteness of Ampère’s law as their cause.
Recall that according to Ampère’s law, the integral of the magnetic field around a closed loop C is proportional to the current I passing through any surface whose boundary is loop C itself:
{∮}_{C}\mathbf{\vec{B} }\cdot d\mathbf{\vec{l} }={\mu}_{0}I.There are infinitely many surfaces that can be attached to any loop, and Ampère’s law stated in is independent of the choice of surface.
Consider the set-up in Figure 16.1.2. A source of emf is abruptly connected across a parallel-plate capacitor so that a time-dependent current I develops in the wire. Suppose we apply Ampère’s law to loop C shown at a time before the capacitor is fully charged, so that I\ne0. Surface {S}_{1} gives a nonzero value for the enclosed current I, whereas surface {S}_{2} gives zero for the enclosed current because no current passes through it:
{∮}_{C}\mathbf{\vec{B} }\cdot d\mathbf{\vec{l} }=\{\begin{aligned}{\mu}_{0}I & & \text{if surface}\,{S}_{1}\,\text{is used} \\ 0 & & \text{if surface}\,{S}_{2}\,\text{is used}\end{aligned}.Clearly, Ampère’s law in its usual form does not work here. This is an internal contradiction in the theory which requires a modification to the theory, Ampère’s law, itself.
How can Ampère’s law be modified so that it works in all situations? Maxwell suggested including an additional contribution, called the displacement current {I}_{\text{d} }, to the real current I,
{∮}_{C}\mathbf{\vec{B} }\cdot d\mathbf{\vec{l} }={\mu}_{0}(I+{I}_{\text{d} })where the displacement current is defined to be
{I}_{\text{d} }={\varepsilon}_{0}\frac{d{\Phi}_{\text{E} } }{dt}.Here {\varepsilon}_{0} is the permittivity of free space and {\Phi}_{\text{E} } is the electric flux, defined as
{\Phi}_{\text{E} }={∬}_{\text{Surface}\,S}\mathbf{\vec{E} }\cdot d\mathbf{\vec{A} }.The displacement current is analogous to a real current in Ampère’s law, entering into Ampère’s law in the same way. It is produced, however, by a changing electric field. It accounts for a changing electric field producing a magnetic field, just as a real current does, but the displacement current can produce a magnetic field even where no real current is present. When this extra term is included, the modified Ampère’s law equation becomes
{∮}_{C}\mathbf{\vec{B} }\cdot d\mathbf{\vec{l} }={\mu}_{0}I+{\varepsilon}_{0}{\mu}_{0}\frac{d{\Phi}_{\text{E} } }{dt}and is independent of the surface S through which the current I is measured.
We can now examine this modified version of Ampère’s law to confirm that it holds independent of whether the surface {S}_{1} or the surface {S}_{2} in Figure 16.1.2 is chosen. The electric field \mathbf{\vec{E} } corresponding to the flux {\Phi}_{E} in is between the capacitor plates. Therefore, the \mathbf{\vec{E} } field and the displacement current through the surface {S}_{1} are both zero, and takes the form
{∮}_{C}\mathbf{\vec{B} }\cdot d\mathbf{\vec{l} }={\mu}_{0}I.We must now show that for surface {S}_{2}, through which no actual current flows, the displacement current leads to the same value {\mu}_{0}I for the right side of the Ampère’s law equation. For surface {S}_{2}, the equation becomes
{∮}_{C}\mathbf{\vec{B} }\cdot d\mathbf{\vec{l} }={\mu}_{0}\frac{d}{dt}[{\varepsilon}_{0}{∬}_{\text{Surface}\,{S}_{2} }\mathbf{\vec{E} }\cdot d\mathbf{\vec{A} }].Gauss’s law for electric charge requires a closed surface and cannot ordinarily be applied to a surface like {S}_{1} alone or {S}_{2} alone. But the two surfaces {S}_{1} and {S}_{2} form a closed surface in Figure 16.1.2 and can be used in Gauss’s law. Because the electric field is zero on {S}_{1}, the flux contribution through {S}_{1} is zero. This gives us
Register to read the full text
This page shows only part of the content. Register or log in to read it all.
Register / Log in