Motional Emf in University Physics

Magnetic flux depends on three factors: the strength of the magnetic field, the area through which the field lines pass, and the orientation of the field with the surface area. If any of these quantities varies, a corresponding variation in magnetic flux occurs. So far, we’ve only considered flux changes due to a changing field. Now we look at another possibility: a changing area through which the field lines pass including a change in the orientation of the area.

Two examples of this type of flux change are represented in Figure 13.3.1. In part (a), the flux through the rectangular loop increases as it moves into the magnetic field, and in part (b), the flux through the rotating coil varies with the angle \theta.

Figure 13.3.1 (a) Magnetic flux changes as a loop moves into a magnetic field; (b) magnetic flux changes as a loop rotates in a magnetic field.
Figure 13.3.1 (a) Magnetic flux changes as a loop moves into a magnetic field; (b) magnetic flux changes as a loop rotates in a magnetic field.

Now let’s look at a conducting rod pulled in a circuit, changing magnetic flux. The area enclosed by the circuit ‘MNOP’ of Figure 13.3.2 is lx and is perpendicular to the magnetic field, so we can simplify the integration of into a multiplication of magnetic field and area. The magnetic flux through the open surface is therefore

{\Phi}_{\text{m} }=Blx.

Since B and l are constant and the velocity of the rod is v=dx\text{/}dt, we can now restate Faraday’s law,, for the magnitude of the emf in terms of the moving conducting rod as

\varepsilon=\frac{d{\Phi}_{\text{m} } }{dt}=Bl\frac{dx}{dt}=Blv.

The current induced in the circuit is the emf divided by the resistance or

I=\frac{Blv}{R}.

Furthermore, the direction of the induced emf satisfies Lenz’s law, as you can verify by inspection of the figure.

This calculation of motionally induced emf is not restricted to a rod moving on conducting rails. With \mathbf{\vec{F} }=q\mathbf{\vec{v} }\,\times\,\mathbf{\vec{B} } as the starting point, it can be shown that \varepsilon=\text{-}d{\Phi}_{\text{m} }\text{/}dt holds for any change in flux caused by the motion of a conductor. We saw in Faraday’s Law that the emf induced by a time-varying magnetic field obeys this same relationship, which is Faraday’s law. Thus Faraday’s law holds for all flux changes, whether they are produced by a changing magnetic field, by motion, or by a combination of the two.

Figure 13.3.2 A conducting rod is pushed to the right at constant velocity. The resulting change in the magnetic flux induces a current in the circuit.
Figure 13.3.2 A conducting rod is pushed to the right at constant velocity. The resulting change in the magnetic flux induces a current in the circuit.

From an energy perspective, {\mathbf{\vec{F} } }_{a} produces power {F}_{a}v, and the resistor dissipates power {I}^{2}R. Since the rod is moving at constant velocity, the applied force {F}_{a} must balance the magnetic force {F}_{\text{m} }=IlB on the rod when it is carrying the induced current I. Thus the power produced is

{F}_{a}v=IlBv=\frac{Blv}{R}\cdot lBv=\frac{ {l}^{2}{B}^{2}{v}^{2} }{R}.

The power dissipated is

P={I}^{2}R={(\frac{Blv}{R})}^{2}R=\frac{ {l}^{2}{B}^{2}{v}^{2} }{R}.

In satisfying the principle of energy conservation, the produced and dissipated powers are equal.

Register to read the full text

This page shows only part of the content. Register or log in to read it all.

Register / Log in