Kirchhoff's Rules in University Physics

We have just seen that some circuits may be analyzed by reducing a circuit to a single voltage source and an equivalent resistance. Many complex circuits cannot be analyzed with the series-parallel techniques developed in the preceding sections. In this section, we elaborate on the use of Kirchhoff’s rules to analyze more complex circuits. For example, the circuit in Figure 10.3.1 is known as a multi-loop circuit, which consists of junctions. A junction, also known as a node, is a connection of three or more wires. In this circuit, the previous methods cannot be used, because not all the resistors are in clear series or parallel configurations that can be reduced. Give it a try. The resistors {R}_{1} and {R}_{2} are in series and can be reduced to an equivalent resistance. The same is true of resistors {R}_{4} and {R}_{5}. But what do you do then?

Even though this circuit cannot be analyzed using the methods already learned, two circuit analysis rules can be used to analyze any circuit, simple or complex. The rules are known as Kirchhoff’s rules, after their inventor Gustav Kirchhoff (1824–1887).

Figure 10.3.1 This circuit cannot be reduced to a combination of series and parallel connections. However, we can use Kirchhoff’s rules to analyze it.
Figure 10.3.1 This circuit cannot be reduced to a combination of series and parallel connections. However, we can use Kirchhoff’s rules to analyze it.

Kirchhoff’s Rules

\sum{I}_{\text{in} }=\sum{I}_{\text{out} }. \sum V=0.

We now provide explanations of these two rules, followed by problem-solving hints for applying them and a worked example that uses them.

Kirchhoff’s First Rule

Kirchhoff’s first rule (the junction rule) applies to the charge entering and leaving a junction (Figure 10.3.2). As stated earlier, a junction, or node, is a connection of three or more wires. Current is the flow of charge, and charge is conserved; thus, whatever charge flows into the junction must flow out.

Figure 10.3.2 Charge must be conserved, so the sum of currents into a junction must be equal to the sum of currents out of the junction.
Figure 10.3.2 Charge must be conserved, so the sum of currents into a junction must be equal to the sum of currents out of the junction.

Although it is an over-simplification, an analogy can be made with water pipes connected in a plumbing junction. If the wires in Figure 10.3.2 were replaced by water pipes, and the water was assumed to be incompressible, the volume of water flowing into the junction must equal the volume of water flowing out of the junction.

Kirchhoff’s Second Rule

Kirchhoff’s second rule (the loop rule) applies to potential differences. The loop rule is stated in terms of potential V rather than potential energy, but the two are related since U=qV. In a closed loop, whatever energy is supplied by a voltage source, the energy must be transferred into other forms by the devices in the loop, since there are no other ways in which energy can be transferred into or out of the circuit. Kirchhoff’s loop rule states that the algebraic sum of potential differences, including voltage supplied by the voltage sources and resistive elements, in any loop must be equal to zero. For example, consider a simple loop with no junctions, as in Figure 10.3.3.

Figure 10.3.3 A simple loop with no junctions. Kirchhoff’s loop rule states that the algebraic sum of the voltage differences is equal to zero.
Figure 10.3.3 A simple loop with no junctions. Kirchhoff’s loop rule states that the algebraic sum of the voltage differences is equal to zero.

The circuit consists of a voltage source and three external load resistors. The labels a, b, c, and d serve as references, and have no other significance. The usefulness of these labels will become apparent soon. The loop is designated as Loop abcda, and the labels help keep track of the voltage differences as we travel around the circuit. Start at point a and travel to point b. The voltage of the voltage source is added to the equation and the potential drop of the resistor {R}_{1} is subtracted. From point b to c, the potential drop across {R}_{2} is subtracted. From c to d, the potential drop across {R}_{3} is subtracted. From points d to a, nothing is done because there are no components.

Figure 10.3.4 shows a graph of the voltage as we travel around the loop. Voltage increases as we cross the battery, whereas voltage decreases as we travel across a resistor. The potential drop, or change in the electric potential, is equal to the current through the resistor times the resistance of the resistor. Since the wires have negligible resistance, the voltage remains constant as we cross the wires connecting the components.

Figure 10.3.4 A voltage graph as we travel around the circuit. The voltage increases as we cross the battery and decreases as we cross each resistor. Since the resistance of the wire is quite small, we assume that the voltage remains constant as we cross the wires connecting the components.
Figure 10.3.4 A voltage graph as we travel around the circuit. The voltage increases as we cross the battery and decreases as we cross each resistor. Since the resistance of the wire is quite small, we assume that the voltage remains constant as we cross the wires connecting the components.

Then Kirchhoff’s loop rule states

V-I{R}_{1}-I{R}_{2}-I{R}_{3}=0.

The loop equation can be used to find the current through the loop:

I=\frac{V}{ {R}_{1}+{R}_{2}+{R}_{3} }=\frac{12.00\,\text{V} }{1.00\,\Omega+2.00\,\Omega+3.00\,\Omega}=2.00\,\text{A}.

This loop could have been analyzed using the previous methods, but we will demonstrate the power of Kirchhoff’s method in the next section.

Applying Kirchhoff’s Rules

By applying Kirchhoff’s rules, we generate a set of linear equations that allow us to find the unknown values in circuits. These may be currents, voltages, or resistances. Each time a rule is applied, it produces an equation. If there are as many independent equations as unknowns, then the problem can be solved.

Using Kirchhoff’s method of analysis requires several steps, as listed in the following procedure.

Kirchhoff’s Rules

  1. Label points in the circuit diagram using lowercase letters a, b, c, …. These labels simply help with orientation.
  2. Locate the junctions in the circuit. The junctions are points where three or more wires connect. Label each junction with the currents and directions into and out of it. Make sure at least one current points into the junction and at least one current points out of the junction.
  3. Choose the loops in the circuit. Every component must be contained in at least one loop, but a component may be contained in more than one loop.
  4. Apply the junction rule. Again, some junctions should not be included in the analysis. You need only use enough nodes to include every current.
  5. Apply the loop rule. Use the map in Figure 10.3.5.

Register to read the full text

This page shows only part of the content. Register or log in to read it all.

Register / Log in