Resistors in Series and Parallel in University Physics

In Current and Resistance, we described the term ‘resistance’ and explained the basic design of a resistor. Basically, a resistor limits the flow of charge in a circuit and is an ohmic device where V=IR. Most circuits have more than one resistor. If several resistors are connected together and connected to a battery, the current supplied by the battery depends on the equivalent resistance of the circuit.

The equivalent resistance of a combination of resistors depends on both their individual values and how they are connected. The simplest combinations of resistors are series and parallel connections (Figure 10.2.1). In a series circuit, the output current of the first resistor flows into the input of the second resistor; therefore, the current is the same in each resistor. In a parallel circuit, all of the resistor leads on one side of the resistors are connected together and all the leads on the other side are connected together. In the case of a parallel configuration, each resistor has the same potential drop across it, and the currents through each resistor may be different, depending on the resistor. The sum of the individual currents equals the current that flows into the parallel connections.

Figure 10.2.1 (a) For a series connection of resistors, the current is the same in each resistor. (b) For a parallel connection of resistors, the voltage is the same across each resistor.
Figure 10.2.1 (a) For a series connection of resistors, the current is the same in each resistor. (b) For a parallel connection of resistors, the voltage is the same across each resistor.

Resistors in Series

Resistors are said to be in series whenever the current flows through the resistors sequentially. Consider Figure 10.2.2, which shows three resistors in series with an applied voltage equal to {V}_{ab}. Since there is only one path for the charges to flow through, the current is the same through each resistor. The equivalent resistance of a set of resistors in a series connection is equal to the algebraic sum of the individual resistances.

Figure 10.2.2 (a) Three resistors connected in series to a voltage source. (b) The original circuit is reduced to an equivalent resistance and a voltage source.
Figure 10.2.2 (a) Three resistors connected in series to a voltage source. (b) The original circuit is reduced to an equivalent resistance and a voltage source.

In Figure 10.2.2, the current coming from the voltage source flows through each resistor, so the current through each resistor is the same. The current through the circuit depends on the voltage supplied by the voltage source and the resistance of the resistors. For each resistor, a potential drop occurs that is equal to the loss of electric potential energy as a current travels through each resistor. According to Ohm’s law, the potential drop V across a resistor when a current flows through it is calculated using the equation V=IR, where I is the current in amps (A) and R is the resistance in ohms (\Omega). Since energy is conserved, and the voltage is equal to the potential energy per charge, the sum of the voltage applied to the circuit by the source and the potential drops across the individual resistors around a loop should be equal to zero:

\overset{N}{\underset{i=1}{\sum} }{V}_{i}=0.

This equation is often referred to as Kirchhoff’s loop law, which we will look at in more detail later in this chapter. For Figure 10.2.2, the sum of the potential drop of each resistor and the voltage supplied by the voltage source should equal zero:

\begin{aligned}V- {V}_{1} - {V}_{2} - {V}_{3} & = & 0, \\ V & = & {V}_{1}+{V}_{2}+{V}_{3}, \\ & = & I{R}_{1}+I{R}_{2}+I{R}_{3}, \\ I & = & \frac{V}{ {R}_{1}+{R}_{2}+{R}_{3} }=\frac{V}{ {R}_{\text{S} } }.\end{aligned}

Since the current through each component is the same, the equality can be simplified to an equivalent resistance, which is just the sum of the resistances of the individual resistors.

Any number of resistors can be connected in series. If N resistors are connected in series, the equivalent resistance is

{R}_{\text{S} }={R}_{1}+{R}_{2}+{R}_{3}+\cdot s+{R}_{N-1}+{R}_{N}=\overset{N}{\underset{i=1}{\sum} }{R}_{i}.

One result of components connected in a series circuit is that if something happens to one component, it affects all the other components. For example, if several lamps are connected in series and one bulb burns out, all the other lamps go dark.

Q1. Some strings of miniature holiday lights are made to short out when a bulb burns out. The device that causes the short is called a shunt, which allows current to flow around the open circuit. A “short” is like putting a piece of wire across the component. The bulbs are usually grouped in series of nine bulbs. If too many bulbs burn out, the shunts eventually open. What causes this?

Answer: The equivalent resistance of nine bulbs connected in series is 9R. The current is I=V\text{/}9\,R. If one bulb burns out, the equivalent resistance is 8R, and the voltage does not change, but the current increases (I=V\text{/}8\,R). As more bulbs burn out, the current becomes even higher. Eventually, the current becomes too high, burning out the shunt.

Let’s briefly summarize the major features of resistors in series:

  1. Series resistances add together to get the equivalent resistance:
{R}_{\text{S} }={R}_{1}+{R}_{2}+{R}_{3}+\cdot s+{R}_{N-1}+{R}_{N}=\overset{N}{\underset{i=1}{\sum} }{R}_{i}.
  1. The same current flows through each resistor in series.
  2. Individual resistors in series do not get the total source voltage, but divide it. The total potential drop across a series configuration of resistors is equal to the sum of the potential drops across each resistor.

Resistors in Parallel

Figure 10.2.3 shows resistors in parallel, wired to a voltage source. Resistors are in parallel when one end of all the resistors are connected by a continuous wire of negligible resistance and the other end of all the resistors are also connected to one another through a continuous wire of negligible resistance. The potential drop across each resistor is the same. Current through each resistor can be found using Ohm’s law I=V\text{/}R, where the voltage is constant across each resistor. For example, an automobile’s headlights, radio, and other systems are wired in parallel, so that each subsystem utilizes the full voltage of the source and can operate completely independently. The same is true of the wiring in your house or any building.

Figure 10.2.3 (a) Two resistors connected in parallel to a voltage source. (b) The original circuit is reduced to an equivalent resistance and a voltage source.
Figure 10.2.3 (a) Two resistors connected in parallel to a voltage source. (b) The original circuit is reduced to an equivalent resistance and a voltage source.

Register to read the full text

This page shows only part of the content. Register or log in to read it all.

Register / Log in