What drives current? We can think of various devices—such as batteries, generators, wall outlets, and so on—that are necessary to maintain a current. All such devices create a potential difference and are referred to as voltage sources. When a voltage source is connected to a conductor, it applies a potential difference V that creates an electrical field. The electrical field, in turn, exerts force on free charges, causing current. The amount of current depends not only on the magnitude of the voltage, but also on the characteristics of the material that the current is flowing through. The material can resist the flow of the charges, and the measure of how much a material resists the flow of charges is known as the resistivity. This resistivity is crudely analogous to the friction between two materials that resists motion.
When a voltage is applied to a conductor, an electrical field \mathbf{\vec{E} } is created, and charges in the conductor feel a force due to the electrical field. The current density \mathbf{\vec{J} } that results depends on the electrical field and the properties of the material. This dependence can be very complex. In some materials, including metals at a given temperature, the current density is approximately proportional to the electrical field. In these cases, the current density can be modeled as
\mathbf{\vec{J} }=\sigma\mathbf{\vec{E} },where \sigma is the electrical conductivity. The electrical conductivity is analogous to thermal conductivity and is a measure of a material’s ability to conduct or transmit electricity. Conductors have a higher electrical conductivity than insulators. Since the electrical conductivity is \sigma=J\text{/}E, the units are
\sigma=\frac{[J]}{[E]}=\frac{ {\text{A/m} }^{2} }{\text{V/m} }=\frac{\text{A} }{\text{V}\cdot\text{m} }.Here, we define a unit named the ohm with the Greek symbol uppercase omega, \Omega. The unit is named after Georg Simon Ohm, whom we will discuss later in this chapter. The \Omega is used to avoid confusion with the number 0. One ohm equals one volt per amp: 1\,\Omega\,=1\,\text{V/A}. The units of electrical conductivity are therefore {(\,\Omega\,\cdot\text{m})}^{-1}.
Conductivity is an intrinsic property of a material. Another intrinsic property of a material is the resistivity, or electrical resistivity. The resistivity of a material is a measure of how strongly a material opposes the flow of electrical current. The symbol for resistivity is the lowercase Greek letter rho, \rho, and resistivity is the reciprocal of electrical conductivity:
\rho=\frac{1}{\sigma}.The unit of resistivity in SI units is the ohm-meter (\,\Omega\,\cdot\text{m}). We can define the resistivity in terms of the electrical field and the current density,
\rho=\frac{E}{J}.The greater the resistivity, the larger the field needed to produce a given current density. The lower the resistivity, the larger the current density produced by a given electrical field. Good conductors have a high conductivity and low resistivity. Good insulators have a low conductivity and a high resistivity. Table 9.3.1 lists resistivity and conductivity values for various materials.
Table 9.3.1 Resistivities and Conductivities of Various Materials at 20 °C
Material Conductivity, \sigma {(\,\Omega\,\cdot\text{m})}^{-1} Resistivity, \rho (\,\Omega\,\cdot\text{m}) Temperature Coefficient, \alpha {(^\circ\text{C})}^{-1}
Conductors
Silver;6.29\,\times\,{10}^{7};1.59\,\times\,{10}^{-8};0.0038
Copper;5.95\,\times\,{10}^{7};1.68\,\times\,{10}^{-8};0.0039
Gold;4.10\,\times\,{10}^{7};2.44\,\times\,{10}^{-8};0.0034
Aluminum;3.77\,\times\,{10}^{7};2.65\,\times\,{10}^{-8};0.0039
Tungsten;1.79\,\times\,{10}^{7};5.60\,\times\,{10}^{-8};0.0045
Iron;1.03\,\times\,{10}^{7};9.71\,\times\,{10}^{-8};0.0065
Platinum;0.94\,\times\,{10}^{7};10.60\,\times\,{10}^{-8};0.0039
Steel;0.50\,\times\,{10}^{7};20.00\,\times\,{10}^{-8}
Lead;0.45\,\times\,{10}^{7};22.00\,\times\,{10}^{-8}
Manganin (Cu, Mn, Ni alloy);0.21\,\times\,{10}^{7};48.20\,\times\,{10}^{-8};0.000002
Constantan (Cu, Ni alloy);0.20\,\times\,{10}^{7};49.00\,\times\,{10}^{-8};0.00003
Mercury;0.10\,\times\,{10}^{7};98.00\,\times\,{10}^{-8};0.0009
Nichrome (Ni, Fe, Cr alloy);0.10\,\times\,{10}^{7};100.00\,\times\,{10}^{-8};0.0004
Semiconductors[1]
Carbon (pure);2.86\,\times\,{10}^{4};3.50\,\times\,{10}^{-5};-0.0005
Carbon;(2.86-1.67)\,\times\,{10}^{-6};(3.5-60)\,\times\,{10}^{-5};-0.0005
Germanium (pure);—;600\,\times\,{10}^{-3};-0.048
Germanium;—;(1-600)\,\times\,{10}^{-3};-0.050
Silicon (pure);—;2300;-0.075
Silicon;—;0.1-2300;-0.07
Insulators
Amber;2.00\,\times\,{10}^{-15};5\,\times\,{10}^{14}
Glass;{10}^{-9} - {10}^{-14};{10}^{9} - {10}^{14}
Lucite;\text{<}{10}^{-13};\text{>}{10}^{13}
Mica;{10}^{-11} - {10}^{-15};{10}^{11} - {10}^{15}
Quartz (fused);1.33\,\times\,{10}^{-18};75\,\times\,{10}^{16}
Rubber (hard);{10}^{-13} - {10}^{-16};{10}^{13} - {10}^{16}
Sulfur;{10}^{-15};{10}^{15}
Teflon^{TM};\text{<}{10}^{-13};\text{>}{10}^{13}Wood;{10}^{-8} - {10}^{-11};{10}^{8} - {10}^{11}
The materials listed in the table are separated into categories of conductors, semiconductors, and insulators, based on broad groupings of resistivity. Conductors have the smallest resistivity, and insulators have the largest; semiconductors have intermediate resistivity. Conductors have varying but large, free charge densities, whereas most charges in insulators are bound to atoms and are not free to move. Semiconductors are intermediate, having far fewer free charges than conductors, but having properties that make the number of free charges depend strongly on the type and amount of impurities in the semiconductor. These unique properties of semiconductors are put to use in modern electronics, as we will explore in later chapters.
Register to read the full text
This page shows only part of the content. Register or log in to read it all.
Register / Log in