Capacitors and Capacitance

A capacitor is a device used to store electrical charge and electrical energy. Capacitors are generally with two electrical conductors separated by a distance. (Note that such electrical conductors are sometimes referred to as “electrodes,” but more correctly, they are “capacitor plates.”) The space between capacitors may simply be a vacuum, and, in that case, a capacitor is then known as a “vacuum capacitor.” However, the space is usually filled with an insulating material known as a dielectric. (You will learn more about dielectrics in the sections on dielectrics later in this chapter.) The amount of storage in a capacitor is determined by a property called capacitance, which you will learn more about a bit later in this section.

Capacitors have applications ranging from filtering static from radio reception to energy storage in heart defibrillators. Typically, commercial capacitors have two conducting parts close to one another but not touching, such as those in Figure 8.1.1. Most of the time, a dielectric is used between the two plates. When battery terminals are connected to an initially uncharged capacitor, the battery potential moves a small amount of charge of magnitude Q from the positive plate to the negative plate. The capacitor remains neutral overall, but with charges +Q and \text{-}Q residing on opposite plates.

Figure 8.1.1 Both capacitors shown here were initially uncharged before being connected to a battery. They now have charges of <span class=+Q and \text{-}Q (respectively) on their plates. (a) A parallel-plate capacitor consists of two plates of opposite charge with area A separated by distance d. (b) A rolled capacitor has a dielectric material between its two conducting sheets (plates)" loading="lazy"/>
Figure 8.1.1 Both capacitors shown here were initially uncharged before being connected to a battery. They now have charges of +Q and \text{-}Q (respectively) on their plates. (a) A parallel-plate capacitor consists of two plates of opposite charge with area A separated by distance d. (b) A rolled capacitor has a dielectric material between its two conducting sheets (plates)

A system composed of two identical parallel-conducting plates separated by a distance is called a parallel-plate capacitor (Figure 8.1.2). The magnitude of the electrical field in the space between the parallel plates is E=\sigma\text{/}{\varepsilon}_{0}, where \sigma denotes the surface charge density on one plate (recall that \sigma is the charge Q per the surface area A). Thus, the magnitude of the field is directly proportional to Q.

Figure 8.1.2 The charge separation in a capacitor shows that the charges remain on the surfaces of the capacitor plates. Electrical field lines in a parallel-plate capacitor begin with positive charges and end with negative charges. The magnitude of the electrical field in the space between the plates is in direct proportion to the amount of charge on the capacitor.
Figure 8.1.2 The charge separation in a capacitor shows that the charges remain on the surfaces of the capacitor plates. Electrical field lines in a parallel-plate capacitor begin with positive charges and end with negative charges. The magnitude of the electrical field in the space between the plates is in direct proportion to the amount of charge on the capacitor.

Capacitors with different physical characteristics (such as shape and size of their plates) store different amounts of charge for the same applied voltage V across their plates. The capacitance C of a capacitor is defined as the ratio of the maximum charge Q that can be stored in a capacitor to the applied voltage V across its plates. In other words, capacitance is the largest amount of charge per volt that can be stored on the device:

C=\frac{Q}{V}.

Note that in, V represents the potential difference between the capacitor plates, not the potential at any one point. While it would be more accurate to write it as ΔV, the practice of using a plain V in this context is nearly universal.

The SI unit of capacitance is the farad (F), named after Michael Faraday (1791–1867). Since capacitance is the charge per unit voltage, one farad is one coulomb per one volt, or

1\,\text{F}=\frac{1\,\text{C} }{1\,\text{V} }.

By definition, a 1.0-F capacitor is able to store 1.0 C of charge (a very large amount of charge) when the potential difference between its plates is only 1.0 V. One farad is therefore a very large capacitance. Typical capacitance values range from picofarads (1\,\text{pF}={10}^{\text{-}12}\,\text{F}) to millifarads (1\,\text{mF}={10}^{\text{-}3}\,\text{F}), which also includes microfarads (1\,\mu\text{F}={10}^{-6}\,\text{F}). Capacitors can be produced in various shapes and sizes (Figure 8.1.3).

Figure 8.1.3 These are some typical capacitors used in electronic devices. A capacitor’s size is not necessarily related to its capacitance value. (credit: Windell Oskay)
Figure 8.1.3 These are some typical capacitors used in electronic devices. A capacitor’s size is not necessarily related to its capacitance value. (credit: Windell Oskay)

Calculation of Capacitance

We can calculate the capacitance of a pair of conductors with the standard approach that follows.

Calculating Capacitance

  1. Assume that the capacitor has a charge Q.
  2. Determine the electrical field \mathbf{\vec{E} } between the conductors. If symmetry is present in the arrangement of conductors, you may be able to use Gauss’s law for this calculation.
  3. Find the potential difference between the conductors from where the path of integration leads from one conductor to the other. The magnitude of the potential difference is then V=|{V}_{B} - {V}_{A}|.
{V}_{B} - {V}_{A}=\text{-}\overset{B}{\underset{A}{\int} }\mathbf{\vec{E} }\cdot d\mathbf{\vec{l} },
  1. With V known, obtain the capacitance directly from.

To show how this procedure works, we now calculate the capacitances of parallel-plate, spherical, and cylindrical capacitors. In all cases, we assume vacuum capacitors (empty capacitors) with no dielectric substance in the space between conductors.

Parallel-Plate Capacitor

Register to read the full text

This page shows only part of the content. Register or log in to read it all.

Register / Log in