In Applications of Newton’s Laws, which introduced the concept of friction, we saw that an object sliding across the floor with an initial velocity and no applied force comes to rest due to the force of friction. Friction depends on the types of materials in contact and is proportional to the normal force. We also discussed drag and air resistance in that same chapter. We explained that at low speeds, the drag is proportional to the velocity, whereas at high speeds, drag is proportional to the velocity squared. In this section, we introduce the forces of friction that act on fluids in motion. For example, a fluid flowing through a pipe is subject to resistance, a type of friction, between the fluid and the walls. Friction also occurs between the different layers of fluid. These resistive forces affect the way the fluid flows through the pipe.
When you pour yourself a glass of juice, the liquid flows freely and quickly. But if you pour maple syrup on your pancakes, that liquid flows slowly and sticks to the pitcher. The difference is fluid friction, both within the fluid itself and between the fluid and its surroundings. We call this property of fluids viscosity. Juice has low viscosity, whereas syrup has high viscosity.
The precise definition of viscosity is based on laminar, or nonturbulent, flow. Figure 14.7.1 shows schematically how laminar and turbulent flow differ. When flow is laminar, layers flow without mixing. When flow is turbulent, the layers mix, and significant velocities occur in directions other than the overall direction of flow.
Turbulence is a fluid flow in which layers mix together via eddies and swirls. It has two main causes. First, any obstruction or sharp corner, such as in a faucet, creates turbulence by imparting velocities perpendicular to the flow. Second, high speeds cause turbulence. The drag between adjacent layers of fluid and between the fluid and its surroundings can form swirls and eddies if the speed is great enough. In Figure 14.7.2, the speed of the accelerating smoke reaches the point that it begins to swirl due to the drag between the smoke and the surrounding air.
Figure 14.7.3 shows how viscosity is measured for a fluid. The fluid to be measured is placed between two parallel plates. The bottom plate is held fixed, while the top plate is moved to the right, dragging fluid with it. The layer (or lamina) of fluid in contact with either plate does not move relative to the plate, so the top layer moves at speed v while the bottom layer remains at rest. Each successive layer from the top down exerts a force on the one below it, trying to drag it along, producing a continuous variation in speed from v to 0 as shown. Care is taken to ensure that the flow is laminar, that is, the layers do not mix. The motion in the figure is like a continuous shearing motion. Fluids have zero shear strength, but the rate at which they are sheared is related to the same geometrical factors A and L as is shear deformation for solids. In the diagram, the fluid is initially at rest. The layer of fluid in contact with the moving plate is accelerated and starts to move due to the internal friction between moving plate and the fluid. The next layer is in contact with the moving layer; since there is internal friction between the two layers, it also accelerates, and so on through the depth of the fluid. There is also internal friction between the stationary plate and the lowest layer of fluid, next to the station plate. The force is required to keep the plate moving at a constant velocity due to the internal friction.
A force F is required to keep the top plate in Figure 14.7.3 moving at a constant velocity v, and experiments have shown that this force depends on four factors. First, F is directly proportional to v (until the speed is so high that turbulence occurs—then a much larger force is needed, and it has a more complicated dependence on v). Second, F is proportional to the area A of the plate. This relationship seems reasonable, since A is directly proportional to the amount of fluid being moved. Third, F is inversely proportional to the distance between the plates L. This relationship is also reasonable; L is like a lever arm, and the greater the lever arm, the less the force that is needed. Fourth, F is directly proportional to the coefficient of viscosity, \eta. The greater the viscosity, the greater the force required. These dependencies are combined into the equation
F=\eta\frac{vA}{L}.This equation gives us a working definition of fluid viscosity \eta. Solving for \eta gives
\eta=\frac{FL}{vA}which defines viscosity in terms of how it is measured.
The SI unit of viscosity is \text{N}\cdot\text{m/}[(\text{m/s}){\text{m} }^{2}]=({\text{N/m} }^{2})\text{s or Pa}\cdot\text{s}. Table 14.7.1 lists the coefficients of viscosity for various fluids. Viscosity varies from one fluid to another by several orders of magnitude. As you might expect, the viscosities of gases are much less than those of liquids, and these viscosities often depend on temperature.
Table 14.7.1 Coefficients of Viscosity of Various Fluids
Fluid Temperature (^\circ\text{C)} Viscosity \eta \times{10}^{-3} Pa ⋅ s
Air;0;0.0171
20;0.0181
40;0.0190
100;0.0218
Ammonia;20;0.00974
Carbon dioxide;20;0.0147
Helium;20;0.0196
Hydrogen;0;0.0090
Mercury;20;0.0450
Oxygen;20;0.0203
Steam;100;0.0130
Liquid water;0;1.792
20;1.002
37;0.6947
40;0.653
100;0.282
Whole blood;20;3.015
37;2.084
Blood plasma;20;1.810
37;1.257
Ethyl alcohol;20;1.20
Methanol;20;0.584
Oil (heavy machine);20;660
Oil (motor, SAE 10);30;200
Oil (olive);20;138
Glycerin;20;1500
Honey;20;2000–10000
Maple syrup;20;2000–3000
Milk;20;3.0
Oil (corn);20;65
What causes flow? The answer, not surprisingly, is a pressure difference. In fact, there is a very simple relationship between horizontal flow and pressure. Flow rate Q is in the direction from high to low pressure. The greater the pressure differential between two points, the greater the flow rate. This relationship can be stated as
Q=\frac{ {p}_{2} - {p}_{1} }{R}where {p}_{1} and {p}_{2} are the pressures at two points, such as at either end of a tube, and R is the resistance to flow. The resistance R includes everything, except pressure, that affects flow rate. For example, R is greater for a long tube than for a short one. The greater the viscosity of a fluid, the greater the value of R. Turbulence greatly increases R, whereas increasing the diameter of a tube decreases R.
If viscosity is zero, the fluid is frictionless and the resistance to flow is also zero. Comparing frictionless flow in a tube to viscous flow, as in Figure 14.7.4, we see that for a viscous fluid, speed is greatest at midstream because of drag at the boundaries. We can see the effect of viscosity in a Bunsen burner flame [part (c)], even though the viscosity of natural gas is small.
The resistance R to laminar flow of an incompressible fluid with viscosity \eta through a horizontal tube of uniform radius r and length l, is given by
R=\frac{8\eta l}{\pi{r}^{4} }.This equation is called Poiseuille’s law for resistance, named after the French scientist J. L. Poiseuille (1799–1869), who derived it in an attempt to understand the flow of blood through the body.
Register to read the full text
This page shows only part of the content. Register or log in to read it all.
Register / Log in